Відео

Good to see you back on!

How did you put the wheels on? It was sped up, so I didn't get it all. What supplies did you use? I have some wheels from a cart, but not sure what things to get to add them on. Thank you!

I RAN ACROSS UR VIDEO WHILE SHOPPING FOR OUR FIRST TILLER N I WAS PRETTY PLEASED WITH THE REVIEW BUDDY... Now, 3 yrs later, is there anything at all you can add to ur first video that a new purchaser would want to know before buying this product?? I thank u in advance for any input u may have for us and GOD BLESS!

How many pallets in total did you use to make this one?

Where is the plug ?

So glad to see you back! I have missed seeing you and your family and critters. Hope to see more of y'all soon.

Glad to see y'all back.

Glad to see y’all back, Chickens are so much fun and so much work too! 😂 It sure has been hot here in MS! 🥵

I DID miss you.🎈💕

Good to see my favorite UA-camr back!

Good to see y’all back! Hope all is well

So good to see you again.

Glad to see you back

Love the floors 😍

Hi Life On The Ridge! Love your house. My husband and I are looking at building something very similar up our way. Would it be possible to get a copy of your plans?

I’m curious to know if notices a taste difference in these compared to the buffs or New Hampshires?

Looks real nice 👍🙂👍

The mistake with the signal lights is not yours. The mistake is that the people that designed the signal lights location had no experience bushhogging. I have knocked mind off several times and I purchased new lights that I am going to mount INSIDE THE ROLL BAR and probably higher than the factory mounts. Use hardware store L brackets and attach with clamps or JB Weld.

❤❤❤WOW

How were you able to insulate between the lower exterior seam of the building, between the metal panels and concrete?

I know this is an old video, but hopefully you can answer this. Did you put anything under your cabinets when you installed them? I have concrete floors and we are doing our kitchen renovation now. I am trying to look everywhere on what to put under the cabinets with no luck. I saw you sealed it and I saw that video on what you used. We are going to do that. But will it help to just seal the whole floor before we put the cabinets on? Or what did yall do? Thank you for your time!!

will you ever do an update video on this floor sealing?

So, you would not recommend spray foam due to the humidity problem?

Awesome! Exactly what I needed. Thank you!

That is awesome… My wife and I are looking to do something similar

Outstanding advice!

Beautiful!!!What would be the total cost including your labor?Thank you

I was wondering to know who was the company that built up your barn . Please respond I need to build up my own . I need to know if they work around my area/state

Did you put any finish coat on the pine walls? Or is it just natural

I think the float is sticking. Mine did that and I tapped it with a screw driver handle.

What kind of permits did you have to obtain? Thinking of doing the same..

I think I'm gonna do one similar to this, bit I can't figure out how to make it predator proof. Where I'm at this would be a racoon buffet. They just dig under. Foxes too.

what cute helper!

Thank you for the very helpful video. I was wondering if you have a blueprint of all the exact measurements you would be willing to share. I would also like to know how many chickens this can hold. Thanks!

Great video! Bout 100 miles south of you in MS!

i think the surge is in the design my dads troy built was the same way is the govener on the carb thats making the surge

I bet thats heavy!

what was total cost with everything building, concrete and all inside work and appliances like plumbing electric A/C

Check the air filter and make sure its not leaking air around the filter (most popular cause of engine rev). Then could be a bad fuel to air mix problem so you might want to check and make sure your choke is adjusted right for what the engine needs to run smooth. There is a mechanism in the crank case area that makes minor adjustments to carburetor air flow to actually prevent surges but if something is blocking it from working correctly (bad oil or debris in the crank case can cause it to not function properly. Normally not an issue with new motors). When you start the engine you want to set the accelerator mid way with full choke. As soon as the engine starts running, reduce choke for smooth running. Once the engine has been running for a while you make want to check the choke is fully off so it won't burn fuel so fast. With the small tank on this tiller it will run out of fuel pretty quick. Hope this helps.

Sometimes there’s a fuel jet that may causes surging. Look up what causes an engine to surge more likely they will say it’s a jet that needs cleaning.

Good job.

This would easily be 2 or 3 times that cost to do this now

Does it require an addiitional circuit breaker ?

Thanks have a smaller one with 18hrs with a stuck clutch going to look for the plug if still there they are going to pay for the repair I hope

Id say new plug and always premium gas I want one of these so bad I like it I like it

My buddies over at Clemmons Concrete Coatings........

Thank you for the information and video.

Congratulations 🎉 Thank you for sharing your family, experience with your home build, and advice. 👏🏽👏🏽👏🏽💯💣🎈

Your home is lovely. Nicely detailed.

RIP Milli you beautiful soul, I know the perfect friend you should meet, her name was Zo another beautiful soul may y’all run free forever☠️🙏